ECMFV (Economy Frame Mount Vertical)

REVERSE OSMOSIS SYSTEM
Model: ECMFV (Economy Frame Mount Vertical)
1,600 to 14,400+ GPD

STANDARD FEATURES

  • Reverse Osmosis Membrane
  • Powder-coated steel frame
  • Stainless steel multi-stage pump
  • Stainless steel membrane vessel
  • High-pressure nylon tubing
  • Liquid-filled high pressure gauge
  • Inlet/Outlet pre-filter gauges
  • Liquid-tight wire shrouding
  • Feed water inlet solenoid valve
  • Adjstbl. waste & recycle s.s. needle valves
  • Product / waste flow meters
  • 10″ 5 micron BB pre-filter
  • High-pressure brass comp. fittings

STANDARD ELECTRICAL CONTROLS:

    • Fused OFF / ON safety switch
    • Flow switch to protect from low/no feed water pressure
    • Float switch for water tank
    • 30 amp motor contactor
    • 110v-60hz  or  220v-60hz

OPTIONS:

  • Nanofiltraion Membrane
    (Removes 98% hardness, up to 85% TDS, high recovery rate)
  • Blending valve +TDS monitor
  • Throttle valve
  • Recycle flow meter
  • Upgrade pre-filter 20″ BB

 

MODEL *GPD Feed TDS
2,000
BELOW ABOVE
Membrane
4″ x 40″QTY
HP
MOTOR
Operating
Pressure
110v-
60hz
amps
220v-
60hz- 1ph
amps
Recovery
rate
PIPING
inlet waste prod
DEMENSIONS
weight lbs.
FMV-1S
FMV-1
1,800+
1,600+
X 1
1
.75HP
1.5HP
150psi
200psi
11.6
20.0
10.4
5.8
50-70% 3/4″ 1/2″ 1/2″
FPT FPT FPT
24″x29″X53″H
140 lbs
X
FMV-2S
FMV-2
3,600+
3,170+
X 2
2
.75HP
1.5HP
150psi
200psi
11.6
20.0
10.4
5.8
50-70% 3/4″ 1/2″ 1/2″
FPT FPT FPT
30″x30″x53″H
166 lbs
X
FMV-3S
FMV-3
5,400+
4,750+
X 3
3
.75HP
1.5HP
150psi
200psi
11.6
20.0
10.4
5.8
50-70% 3/4″ 1/2″ 1/2″
FPT FPT FPT
30″x30″x53″H
194 lbs
X
FMV-4S
FMV-4
7,200+
6,340+
X 4
4
2HP
3HP
150psi
200psi
19.2
n/a
9.8
13
50-70% 3/4″ 1/2″ 1/2″
FPT FPT FPT
30″x30″x56″H
236 lbs
X
FMV-5S
FMV-5
9,000+
7,900+
X 5
5
2HP
3HP
150psi
200psi
19.2
n/a
9.8
13
50-70% 3/4″ 1/2″ 1/2″
FPT FPT FPT
30″x30″x56″H
267 lbs
X
FMV-6S
FMV-6
10,800+
9,500+
X 6
6
2HP
3HP
150psi
200psi
19.2
n/a
9.8
13
50-70% 3/4″ 1/2″ 1/2″
FPT FPT FPT
30″x30″x56″H
293 lbs
X
FMV-8S
FMV-8
14,400+
12,670+
X 8
8
3HP
3HP
150psi
200psi
n/a
n/a
13
13
50-70% 3/4″ 1/2″ 1/2″
FPT FPT FPT
30″x40″x56″H
320 lbs
X


FEED WATER PARAMETERS:

  • Temperature: 85° F maximum
  • Pressure: 40 – 80 psi maximum
  • TDS: 2000-5000 ppm maximum (Consult Dealer for specific model)
  • Iron tolerance: 0.5 ppm maximum
  • Hydrogen sulfide: must be removed
  • Silica tolerance: can not be higher than 100 ppm in the concentrate stream.
    (Antiscalant should be considered for any levels over 75 ppm)
  • Turbidity: should be removed
  • Hardness: must be removed


OPERATING PARAMETERS:

  • Operating pressure: 150 – 200 psi maximum
  • Water recovery: up to 70% and is field adjusted by customer.
    (It is not recommended that the recovery be set higher than 70%)
  • pH range: 3 – 11
  • Flow rates are determined by the membrane mfg.’s. testing criteria of 1500 ppm Nacl solution, 77°F water temperature, 225 psi at 10-15% recovery. Typical membrane salt rejection is 95-99%

*Actual flow rates may vary depending on the pre-treatment used, water conditions, feed water temperature and applied pressure, etc.